0
Ford Explorer Sport Trac
Built from 2001 to 2010, the Ford Explorer Sport Trac was a mid-size sport utility vehicle (SUV) with a pickup truck bed. Produced in two generations, this model was mainly sold in North America.
1,557 Questions
How do you disassemble the front driver side door on a 93 Buick Roadmaster?
The first step is to find a single Phillips screw hidden in the carpet on the lower rear side of the panel. It is approx 5 inches in and 4 inches up. Remove it. Next, peel each end of the grab handle inward to reveal a single large Phillips screw (1 per side). Remove the screws. Next remove the single screw behind the interior door handle and remove the door handle surround over the hadle itself. the rest of the fasteners are snap type. Start at the bottom using the special door fastner tool to release. You can just pull forcefully, but it usually breaks these fasteners. Once the door is only hanging from the top strip, remove all elecrical connections. Next roll down the window and pull upward on the panel to release it from the lower window strip. Installation is reverse of removal.
How do you get the door locks on passenger side and back doors to unlock on 2003 Ford Crewcab?
if some doors are not unlocking, i would test the door lock master switch you migh also check that the master switch is not locked fords have a lock/unlock swith on the switch panel to stop all other doors working easy way to test master control switch is to remove switch from door,and disconect the wire plug in. use a jumber wire to cross the terminals to each door from power supply if the switch is bad,each door will unlock when crossed. so if doors will unlock this way, replace switch other than that the only other problem i have found is the actuators inside the doords. these are a pain to replace and are not cheap as each door has one. try the switch first
email me at dwightdbs@yahoo.com . I have the same problem.
How do you reset the service engine soon light not the oil reset light on a 2001 Chevy Silverado?
One way:
I pulled out the ECM fuse located in the fuse box under the hood right under the engine fuse. I pulled it out while the truck was running. The truck shut off. Then i put the fuse back in and restarted the truck, and the light was off.
How do you take off the front driver side door panel of a '92 Chevy s-10 blazer?
First there are 2 Philips head screws in the armrest, remove those and put them aside.
If you have power windows and doors, pop out the switches, careful not to lose the retaining clips, and disconnect the electrical connectors on the switches and put them aside.
If you have manual locks, unscrew the knob. If you have manual windows you should invest in a special door handle removal tool which will easily partially back off the hidden C clip allowing you to pull the handle straight off.
Next use a wide putty knife (or the special tool you can buy) slip it between the door panel and the metal of the door itself, and gently pull on the panel.
Start at the bottom rear corner and move around the door panel, about 6 inches at a time, until the panel is loose and pretty much hanging off the door.
Now lift the door panel up gently and voila.
Can you please post the instructions on how to set the code?
The keyless entry pad can use two codes to unlock the doors, the factory code and your own personal code. To program your own personal entry code into the keyless entry pad , select five digits that are not in sequence or use the same button five times. 1 - enter the factory set code 2 - within 5 seconds, press the 1/2 button 3 -within 5 seconds of pressing the 1/2 button, enter your personal code, pressing each digit within 5 seconds of the previous digit. The keyless entry system registers this second code, so you can unlock the doors with the factory code or your personal code.
On my 1988 Cutlass Supreme the cable broke at the release point in the car. I was unable to see anything from the outside so in the passenger compartment I took the release handle apart and used a set up pliers to pull the cable and release the hood. There should be just on bolt holding the release in place, it may be covered by the carpet. If it can't be done from the inside you can also reach up from under the front bumper and find the cable where it attaches to the latch. Just pull the cable and the hood should release.
How long is the drive cycle on a 2001 ranger?
Pre-reqs:
Cold soak vehicle for 8 hours
Make sure codes are cleared
Fuel filled between 15 and 85 %
-Start & idle vehicle for 4 min.
-Idle vehicle in drive for 40 sec.
-accelerate to 45 mph using 1/4 to 1/2 throttle
-accelerate for at least 10 seconds, shifting through to 5th gear
-drive with a steady throttle at 45 mph for 30 sec.
-stop the vehicle and idle in either drive or neutral for 40 sec.
-drive at speeds between 25 and 45 mph for 15 min. Use 1/4 to 1/2 throttle accelerations. Include the following conditions:
-at least 5 stops within 10 sec of idle time
-at least 3 steady speed sections of
1 1/2 min durations
-drive the vehicle between 45 and 60 mph for 8 min (use high gear)
-maintain a steady speed between 45 and 60 mph for 5 min
-drive the vehicle between 45 and 60 mph for 8 min (use high gear)
-stop vehicle and idle for 40 sec.
This is one of the more involved drive cycles, and from experience, takes a long time, so be patient and be prepared, Good luck!
Where is the F350 front kick panel?
There are 2, in front of the door under the dash. Between the dash and the floor. Theres one on the driver side and one on the passenger side.
It is a condition when one or more cylinders on an engine does not fire properly and completely burn the fuel/air mixture. It can be caused by a defective spark plug, bad plug wire, defective fuel injector, burnt valve, cracked piston, blown head gasket, or cracked head.
How do you stop the beeping noise on a 1995 caprice when the instrument panel lights are on?
its eather a fuse is blowen or one of your bulbs are blowen
Where is the horn located on a 1993 Cherokee Sport?
Most have one horn under each fender in the front. My 03 Sport has 1 horn just under the left front turn signal lamp. from underneath move the tar type paper and it is held in place by one 1/2" bolt. Try emery cloth on the contact before replacing horn.
How do you change the front brake pads on a ford focus?
Brake jobs are not a job to be done without a Manual. Your life and the lives of others and the life of your Automobile depend on them.
Please purchase a Manual and do the job correctly. Or Hire someone who can.
Loosen the lug nuts by turning them counterclockwise 1/2 turn.
Raise the Focus up and put it on jack stands. To do this, place the floor jack under the the Focus and jack up on the front jack point. Then, place the jack stands under the front pinch welds and lower the Focus onto the jack stands.
Continue to remove the lug nuts and then remove the wheel.
Remove the caliper mounting bolts holding the caliper in place.
Lift the caliper off the hub assembly and secure it with zip ties to the coil springs above the brake assembly.
Remove the brake pads. You may need to tap them out with a rubber mallet.
Press the caliper piston back into the caliper. Place the face of a brake pad against the caliper piston and squeeze the piston back into the caliper using the c-clamp.
Insert new brake pads and reassemble the brake system.
**NOTES**
Ensure the disc is clean and free of oils and dirt
Use threadlocker on the caliper bolts to prevent them from losening while driving or heavy braking.
Bleed the brake fluid lines to remove and air bubbles. Air could cause soft pedals or dead zones during braking.
Put the wheel back on, finger tighten lug nuts. Lower the vehicle, and torque the lug nuts to 100 foot-lbs with a torque wrench.
How do you reset the service engine light on a Aztek?
This has to be done with a OBD2 scan tool. You might be able to get your local Auto Zone or Advanced Auto parts to do it. But different government agencies have been telling them not to do it. So you either have to buy the scan tool to do it, or pay to have someone else do it. Its cheaper probably to do it yourself. I think Auto Zone has a small hand held scanner tool for 50 bucks or so. Its the same tool they use to scan your car if you ask them too. Ask them to borrow it so you can reset your light, sometimes the let you do that too..
*** You may also try disconnecting the battery for around 20 minutes. That should reset the ECU also.. Nice and cheap*** If your vehicle still has a problem going on that its sensors find, it will still appear after a moment.
How do you replace the instrument panel and back-up lights in a 1986 Chevy Corsica?
Hard to do , didn't Corsicas only start in 88??
What does the remainder in a division problem tell you?
the divisor can not have that number going into the dividend anymore.
What is causing your 05 explorer sport trac with a 4.0l v6 to studder only at idle?
check the idler pully is not siezed start the truck and have someone give it a little gas or reach under the trottle body and pull on the linkage to the trottle body to give it fuel watch the idler pully should move a bit to tighten or loosen the belt and all ...if ideler pully seized the idel of the truck will sputter ,,,,,
could also be a bad spark plug with i had on my 2004
causing the truck to miss fire on one cylinder ,, which was more noticeable at low idle
What fuse number is the 12 volt supply outlet for a 2003 ford sport trac?
#22 is a 20 amp fuse for the instrument panel Power Point in the fuse panel
in the drivers end of the dash
Low Trac means Low Traction. if the light goes on, it means your car noticed that your wheels are spinning. Especially in winter, slow down and let your wheels grip the road. Spinning tires will make ice beneath it.
How do you get to and remove the coil packs on a 1999 S-10 with a 22 liter engine?
They are located on the passenger side of the engine. How you get to them is a matter of the degree of contortionist you are.
Basically, remove all spark plug wires (number them as you go, according to the coil pack numbers).
Each coil pack has 2 nuts, I believe they are 7/32 or 7mm nuts. Pull off the coil packs, install the new ones, replace the wires according the numbers you recorded.
Have a nice day.
I have found that if you remove the passenger side front tire that you can access the coil packs easier. There is a small flexible panel that you can fold away to reach the coil assembly.
How many are there on the 4.3 L Will that explain multiple misfire code?
How do you reset a service engine light on a 1997 Nissan Maxima?
First you have to locate ECM which is on the driver side just below the steering wheel and just right of gas pedal. You will be able to see ECM after removing a plastic cover. After that you will see a nut in that ECM, which needs to be turned clockwise and then anticlockwise. This is to be repeated three to four times with a span of 15-20 seconds. Next time you will start your car the annoying "Check Engine Light" should go away.
How do you get the lower steering wheel cover off over the tilt lever on a 2001 Ford Sport Trac?
The lever for your tilt steering is threaded and screws on
Thank you very much for the answer. I did finally figure that out when I was able to se inside with a flashlight. I appreciate your response.
Where is the inertia switch in a 2004 Ford Explorer trac?
According to the 2004 Ford Explorer Sport Trac Owner Guide :
The fuel pump shut off switch ( inertia switch ) is in the front passenger
footwell , behind the kick panel access cover
* the kick panel is the interior trim panel , in front of the front door , by the passengers feet
