0
Ford Explorer Sport Trac
Built from 2001 to 2010, the Ford Explorer Sport Trac was a mid-size sport utility vehicle (SUV) with a pickup truck bed. Produced in two generations, this model was mainly sold in North America.
1,557 Questions
2002 cavalier yellow check engine light is turning on why?
there is a code set by the cars computer. you need to have the car scanned to see what the code is. alot of the times getting gas while the car is running can set a check engine lite. There is a difference between the service indicator light (yellow) and the check engine light (red). Also, to those people who say check the manual, we did. The manual gives the smallest description in the book for this light. It says to see the dealer service department. It doesn't give any examples as to what the problem could be.
How do you remove the front drivers side door panel on a 2001 Saturn L200?
remove the door and window crank handles with a special tool from the parts store, Then all of the screws you can find esp at the corners. Then the retainers with a special tool around the sides and botton fo the door.This is not an easy job.
You will have to remove the mounting bracket that holds the engine up. It is more than a motor mount, it is the brace under the car that the engine rests on. For about 80 bucks, you can buy a frame that sits where you hood normally does to hold the engine up when you remove this brace.
How to fix a Scooter flooded engine?
my fix for flooded engines is to remove the spark plug, and heat it with a propane torch until it glows ,so that all fuel and deposits burned away.
That's asking for trouble. You are likely to set your scooter and your whole garage on fire. Simply remove the plug and let it evaporate over time. It won't take long, gasoline evaporates very quickly.
Is there warranty on a motorcraft battery after 3years?
On my Motorcraft BXT-65-650 battery there is 3 years replacement warranty
and then the warranty is pro-rated for a total of 100 months from the date of
purchase ( I had the battery purchased / installed bya Ford dealer after
they checked the charging system , if that makes any difference )
Where you can get a wire harness?
A company called painless wire harness Auto wrecking/salvage yards are also very good options if the harness doesn't need to be new.
Where is the Low pressure ac charge inlet on a 2000 expedition?
I think it is just behind the transmission dip stick under the box.
How do you replace the instrument panel lights on a '01 Explorer Sport Trac?
The headlight switch instrument panel illumination bulb can be accessed / replaced without removing the dash (on an 01' & possibly other) Explorers, though it is a bit tricky. The bulb is seated in the switch itself, and is removed with a quarter turn counter clockwise. You'll need a small slot screwdriver with a narrow blade (or similar item) to do this. To get to the bulb, you'll need to pull off the fuse panel access door and remove the three (3) screws holding the fuse block. You'll also need to remove the plastic trim panel under the steering wheel, including the hood latch (7mm socket). Underneath that is a metal, wiring cover plate, which also must be removed (9mm socket). Once all are out of the way you can get behind the switch and using a small screwdriver, remove the old bulb and replace. It appears all other instrument panel lights have to be accessed via complete removal of the dash.
If the lights behind your gas gage, mph gage, or etc. are not working, you will have to remove the panels below and above your steering wheel. I'm unsure of the bulb size, but you can go to the auto parts store and tell them what you need and they should give you the correct build. There's 6 total, and i replaced all 6 when i replaced mine because they are so complicated to get to.
1. remove the panel which holds your CD player and heat/air controls. Remove the controls on your heat/air by just pulling them off. Remove the two screws directly above the controls. Pull out on the entire panel and it will snap off.
2. Remove the panel below your steering wheel by taking two screws at the very bottom of the panel out. Pull the panel out and it will snap off.
3. Remove the metal plate behind the panel you just removed by taking the 5 bolts out in the plate.
4. Remove the panel which contains your dimmer and lights on/off switch by removing the 3 screws underneath the dash. Look and the glass panel then look up, you'll see the 3 screws. Pull out on the panel and it will release.
5. Remove the whole instrument panel by taking the 4 bolts out in each of the 4 corners. The instrument panel will come out.
6. Look on the back of the panel. There will be a circuit board. There will be six black bulb holders which will snap out of the circuit board. Twist the black bulb holders counter clockwise about 1/4 turn and they will snap out. The new bulbs will fit in the place of the old bulbs. Put the black bulb holder back in the circuit board and turn clockwise 1/4 turn.
7. Replace all of the panels just like you took them off.
Where do you find the key less entry code on a 2003 Explorer Sport Trac?
The master code is in the front of the owners manual, you can also input your own code if you have the master code, details inside manual.
How do you reset the service engine light and the low washer fluid light?
To Reset the lights disconect the negitave lead on your battery for about 5 to 10 min then reconnect, it light is still on then you could have a bad sensor.hope this helps, Even easier.... on the fuse panel..remove the fuse for the Electronic control module for 10 minutes ( does the same thing as disconnecting the battery) then push it back in..should clear any stored codes
I had the same problem and soon discovered that I was out of transmission fluid. The way I discovered this of course was the stream of fluid I left right before this happened. I looked beneath the vehicle to find the entire underside covered in transmission fluid, and discored it had been leaking from the Accumulator Piston Cover on the front passenger side of the transmission housing. It is a small round black plastic circle with an indentation in the center which you can see clearly if you cut your wheels to the left and look behind the passenger side front tire at the transmission housing. I ordered a new cover from my local Isuzu service center, $23.00 and some change shipping and part, and you use a snap ring tool, inner type, to remove the old one and snap the new one in place. Then you can use 3/8 inch outer diameter tubing with a funnel held high and pour the transmission fluid into the fill hole on the bottom of the tranny pan until it runs out of the overfill hole up top. Then start the motor and let it get to idle temp, and the tranny fluid will start to circulate and you can continue filling the tranny. According to Oreilly's Auto Parts a fresh fill takes 9 quarts of Dexron III ATF.
2001 and newer Explorers have a separate control module for the 4x4 system it is mounted behind the right front passenger kick panel . Helpfull
How do you remove the dash on a 1996 caprice?
To remove the dash locate the 7mm hex screws that hold the lower edge of the dash to the car. Remove all visible screws. Pull out the ashtray and remove four more 7mm Hex screws and then unplug the little light assembly. Remove the ashtray drawer. Put the parking brake on, turn the key to on, and move the shift lever down to L1. Remove the two 7mm hex screws that hold the black instrument cover on, these are located at the top of the instrument cluster. After this has been removed, see another hex screw on the left wall inside the instrument cluster. Remove it as well. The rest of the dash snaps out but you must pull straight towards yourself and do not rock or twist the dash panel . It will snap out. It is very easy to break the little plastic nibs that hold the dash panel on.
Can you drive with a coil gone and light flashing?
As far as I know you can drive it in for repair when the check engine light is
flashing indicating an engine cylinder misfire . Just avoid any heavy /
rapid acceleration or deceleration because you can damage the catalytic
converter ( P.S. I'm not a mechanic / technician )
How do you reset the service engine light on a 2003 Infinity I35?
1. Sit in the driver's seat and turn the ignition switch ON, but don't start it.
2. Wait exactly 3 seconds.
3. Quickly push the accelerator down fully (and fully release it) 5 times in less than 5 seconds.
4. With your foot away from the accelerator, wait exactly 7 seconds.
5. Push and hold the accelerator for 10 seconds until the CEL/SES light starts to flash. Wait a bit, and if it doesn't start to flash a moment after that 10 seconds, turn the ignition off and try again until you get it right. You may have to try a few times.I used my head but you may prefer a timer or a watch.
6. Fully release the accelerator pedal while the SES light is still blinking.
7. Wait 10 seconds.
8. Full press accelerator down for MORE THAN 10 seconds this time, then full release the pedal. (SES Light will continue blinking)
9. Immediately turn the ignition switch to “OFF†position, then after a couple seconds start the car. The SES will be off!
It took me a few tries to get it, but it WORKED on my 02 Infinity i35...
The flashing light will tell you the 4 digit fault code, but all I wanted to do was reset the SES warning light after I had a backyard mechanic perform the necessary work.
Yes, there are about 6 bolts on each side you have to remove, you do not have to remove the molding, just use the access panels, however you have to pull the center part out, (3000GT part) a bit to remove the tail light.
What is the wiring colors for a earthquake PA - 2075 AMP?
Earth Quake:
Red is L+, Purple is L-, White is R+, Brown is R- , Orange is Remote
Why are the instrument panel lights off when the rest of the lights are working?
your instrument panel lights can be dimmed(thumb wheel switch) down to practically no lights at all on your instrument cluster, this switch should be located most likely on the dash, left hand side of steering column. If this does not fix the problem ,then you have to check your fuse panel to see if you have a burnt out fuse.
2005 caravan power windows not working?
Check the fuses in the power distribution block - usually under the hood
How do you disassemble the front driver side door on a 93 Buick Roadmaster?
The first step is to find a single Phillips screw hidden in the carpet on the lower rear side of the panel. It is approx 5 inches in and 4 inches up. Remove it. Next, peel each end of the grab handle inward to reveal a single large Phillips screw (1 per side). Remove the screws. Next remove the single screw behind the interior door handle and remove the door handle surround over the hadle itself. the rest of the fasteners are snap type. Start at the bottom using the special door fastner tool to release. You can just pull forcefully, but it usually breaks these fasteners. Once the door is only hanging from the top strip, remove all elecrical connections. Next roll down the window and pull upward on the panel to release it from the lower window strip. Installation is reverse of removal.
