0
Toyota SR5
Manufactured by Toyota Motor Corporation, the SR5 (Sport Rally 5-Speed) belongs to the Hilux pickup truck product line. The Toyota SR5 was a popular option package in the North American market.
941 Questions
Where is the wheel cylinder located on my 1986 dodge truck?
I assume you're talking about the wheel brake cylinders. There is one on each wheel. The two in front clamp the brake disks. The two in back are inside the back drums.
Why must you install power commander when changing exhaust on fuel injected motorcycles?
The exhaust system will change the air flow to the engine so the power commander is needed to re-map or calibrate the system again so that it is optimized. If you don't re-map the system then you will not get the full benefits of the exhaust.
Where is the vacuum hose on a 93 Tempo?
There is more than one vacuum hose. Which one? The one that controls the opening and closing of the vents for cold air distribution
It can be any of that plus a loose wheel, bent wheel, loose wheel bearing, etc. Whatever it is, it is a dangerous situation. Get this looked at ASAP. Do not continue to drive this car.
How do you roll down the rear windows in a 1991 lebaron?
The drive motors for the rear sit at the bottom of the window wells. Water runs into the area, and if the drain holes are not kept clear then water builds up above the level of the vent holes in the bottom of the motors. The entire window assemble can be removed, held by only three bolts (don't cut the back of your hands in this area). Either replace the motors, or clean the insides of the brush and contact area with a dremel wirewheel. Lube with white grease do slow the return of the corrosion.
If a throw out bearing is bad will that also sound like a main bearing going bad?
No, main bearing noise is a rumble Throw out/release bearing for the clutch will only be heard when the clutch pedal is depressed. If you hear the noise without the clutch pedal being depressed, it is most likely the gearbox first motion shaft bearing that is at fault. First motion shaft bearing noise usually goes away when the clutch pedal is pressed.
Why your 94 Toyota pickup V6 groans when steering or taking corners?
the power steering pump is worn out making internal gears of said pump produce that groaning noise. if not taken care of it will aventually fail.
Where is the PCV valve on a 1987 300zx non turbo?
The PCV valve is located on the passenger side of the vehicle about center of the air collector system cover. It's right on top and easy to see and replace. Just remove the hose connected to it and screw the valve out of the intake manifold. Install is the reverse. You may want to check the valve first before replacing it. To do this, just remove the ventilation hose attached it and start the engine. If you hear a hissing sound coming from the valve while the engine is running, the valve is good. Also, if you place your finger over the mouth of the valve you should feel a strong vaccum pull. That would also signify a working valve.
Where is the water pump located on a 1998 GMC Sierra extended cab pick up?
Open the hood of your truck. Look inside the engine bay. See the fan assembly and the pulley that the belt rides on. The water pump is behind the pulley. Changing water pumps can be somewhat of a task. Professional help will be needed for someone that can't find the waterpump.
Dash lights on a 1991 Pontiac Firebird won't turn off even when car is off. How do you fix this?
take battery cable off its a tempary fix but you have something behind the instrument panel blown
What is the tire size for a 1992 Toyota pickup?
the proper tire size should be printed on a label on the drivers side door jam i have a 1992 Toyota 4wheel drive and mine takes P225\75 -R15
How do you fix a fuel gauge on a 1985 Ranger pickup?
The ranger has a fuel sending unit inside the gas tank. These are notorious for going out. Only way to change it is to drain and drop the gas tank or remove the bed. The sending units that I have been looking at cost about $100
code 44 -02 sensor indicates a lean problem,code 45 is a rich problem,check the ecm wiring connections,#15 and#8 check also for a vaccum leak at the tbi base gasket.a code 33 or 34 indacates a faulty map sensor,my 89 Chevy 4x4 read code 44 followed by code 34 which turned out to be my vaccum line to my map sensor was off.
Where can you find the EFI fuse on a 1988 Toyota pickup?
On my 89 it is in the fuse box under the hood on passanger side 15 amp closest to the firewall
Does the 1993 Toyota pickup have a r134 ac system?
it is a mid year split in 1994. 1993 should all have been r12.
How would you know if you have a leaky water pump on a 1997 Toyota 4Runner?
You will know if you have a leaky water pump because it will be leaking coolant out of the water pump.
Problems with overheating on a 1988 Chevrolet Nova?
Your car can be over heating because the water pump might be getting old and starting not to make the flow of water as fast. But also your water pump might not be pushing enough water through your motor if your car is built up..........
Your 89 Toyota pick up truck is running low to no power?
My 1986 4WD pu intermittently had low to no power and it was due to the fuel pump. Replaced the pump and it ran fine.
Where is the PCV valve on a 2.0L 1988 Ranger?
Coming out of intake manifold and going into rocker cover
The throw out bearing will only make noise when you press the clutch pedal. If the clutch is new, the throw out bearing is a required replacement in a clutch job. Sounds like a bad pilot bearing. Not enough info in the question.
I had the same problm and it was input shaft bering, AND the counter shaft bering. Replace them and sloved the problm.
Where is the PCV valve on a 1986 Pontiac 6000 STE?
to the Owner of the 1986 STE: I own two 1985's STE's and I noticec the PCV valve is on the front valve cover. I hope this will be of some help. Most Sincerely, Kristopher Gerbracht www.kristopher.gerbracht@juno.com
Where is the PCV valve on a 1998 expedition?
on the left falve cover close to the firewall (small black plastic cilinder with black rubber hose on top) just pull out to remove.
