0
Ford Windstar LX
Introduced in 1995, the Windstar LX was a first generation Windstar model powered by a 155 hp 3.8 L V6 engine, which can generate up to 220 lb ft of torque.
1,653 Questions
Where can you find the diagram for the vacuum hoses on a acura integra?
It is important to have a diagram when making any changes to a car. A diagram for an Acura Integra's vacuum hoses can be found in the cars maintenance manual.
Where do you put freon in 95 windstar?
if you bought a cheap kit thing at the auto parts store it will only conect to the low presure side(thats where you want it), profetional sets are more compicated(if you dont know what your doing back away, let a pro do it)
Where can you find a diagram for a 1998 Dodge Neon 2 liter twin cam overhead vacuum assembly?
Buy a chilton manual at your local autoparts store these diagrams are usually in the back of the book.. D
Why is the speedometer not working?
The sensor in the differential may be bad. Also the wires going to the sensor may have rubbed against a brake line causing them to short. The sensor in mounted on top of the differential and reads the vehicle speed.
Where can you find a vacuum hose diagram for a 1978 Buick Skylark with a 3.8 liter V6?
Should be on the underside of the hood. The parts dept of your local GM dealership should be able to help you. They WILL print one up if you ask nicely! There is not a whole lot of vacuum routing on that year! Call 1.800.462.8782 General Motors they are generally helpful. I have had them mail me al kinds of out-of-print 'stuff'. Y-THINK-Y
How do program 1997 ford expedition key with new transponder?
Far as I have been researchin on the web there is a few steps that you can perform, like enter the master key (its 100% requier) and turning the car on for like 15 sec, then you turn it off, and insert the new transponder key, and turn the car on, and leave it running for about 10 min, but up to this point I{m still waiting for my new tranponder keys to test it, check on the web, since I read there is a posibility to lock your car on programming if its not propertly done.
Still I will post back my experience if I make it work, believe me I´m not agree to pay over $100 to dealer´s for a spare key.
What is the spark plug gap for a 1995 Mercury 60hp?
It should be .040 and the NGK Spark plug for that is a BP8H-N-10 or a Champion QL78YC/L78YC I am not sure what the AC delco number is, but they all should be .040
Where is the driver side power window fuse?
There is no single fuse for one power window. The most common thing is the switch to fail. This would be the master window switch. Try jumping the wires with a live current and see if the window goes up and down. If it does then its your switch, if the motor fails to move most likely its the motor/regulator.
What is the spark plug gap on a 1996 Ford F-150 5.0 V8?
Start by looking in the owners manuel. ---------------------------------------------------- unfortunately , the 1996 F-150 owners manual doesn't show the spark plug gap or firing order for any of the engines , but www . motorcraft . com ( no spaces ) shows the spark plug gap for the 5.0 L V8 engine as ( .054 inch ) and the 4.9 L straight 6 cylinder / 5.8 L - V8 engines spark plugs are gapped at .044 inch
What is the gross weight of a 1986 Chevy Astro van?
I dont know if this is the gross weight or net weight but here goes. I just scraped a 86 Astro. Basically nothing but body engine, trans, tires,rims all factory. All seats interior etc were taken out. 3300lbs.
got $300 for it lol. But it's been sitting in field for ten years so that's ok.
There are several possible answers to this problem. First, check to see if you have brake lights. If not, check the fuse that supplies power to the brake lights. (my 2001 outback is #16 20amp located behind the coin drawer in the dash). If it is blown, replace the fuse and push on the brake pedal. If it blows again, you have a short in the system. Most common fix is to replace all the brake lights. Sometimes they short out the system, blow the fuse and that will keep the car from shifting out of park. If the brake lights do not keep the fuse from blowing, it could be the brake solenoid located at the top of the brake pedal, or it could be the shift lock solenoid located to the right of the shifter under the cover. The easiest way to check these items is to unplug the wiring harness one at a time and then replace the fuse and see if it blows when you press on the brake. My fix was the shift lock solenoid. It isn't super hard to replace and can be found online or at a local wrecking yard.
I have a '94 Subaru Impeza and I took all the plastic parts out from around the shifter and on the right side is the locking pin that rises and falls when you pushed the button. This tends to get dirty and sticks. Clean as much as possible and spray WD-40 or silicone. It will take care of the problem.
I also found that if you have a weak battery or bad battery connection this can also cause the same issue.
How do you change a parking brake cable on 300zx?
This is for the 84-89 300ZX. There are 3 separate pieces that go with the Parking Brake. 1) The handle on the center console which has a cable connected to it, which in turn goes through the floor to a Y type cable connection. 2) Left side cable connected to the rear brake caliper that is channeled through the fame a few inches with clips that keep it in place. 3) Is the same as 2 but on the right side. I will have t assume that your cable is rusted and seized up. If the #1 cable seizes, you have to replace the whole handle piece which comes off with 4 bolts, 2 on handle and 2 for the cable that passes through the floor. The other two, you have to take the rear tires off and get under the car and take off the clips that hold the cable to the frame. Pull the cable out through the frame and replace.
Where is the powertrain control module located in a 95 ford windstar lx?
Engine compartment passenger side firewall, remove wiper arms and plastic cowls. Unplug connector remove two nuts, plastic cover and slide pcm out. Book time is one hour.
How do you remove the backseats in a Ford Windstar?
There is a release lever at the rear seat mounting point on each side. Pull the levers - tilt the rear of the seat upwards - pull the entire thing towards you. Very often, I find the release levers kinda jammed and won't pull - I use a large screw driver to get some extra leverage and pop the release open. This is a tough job for one person! There are 2 seat release handles located on the backside of the seat assembly - down at the floor.
It may take some leverage to pull them back and release the latches, but when they are both pulled, use those same levers to lift / tilt the seat up, and then towards the rear of the vehicle.
How much does it cost to have the water pump replaced on a 1998 GM Sierra?
Should be between $125.00 and $200.00, If there is no other work to be done do not agree to pay more than $200.00, The parts are about $40.00 and the time is about 2 hours.
Where is the PCV valve and how to install on a Windstar?
PCV Valve locations:
- 1995-1998 3.0l - front valve cover
- 1996-1998 3.8l - rear valve cover
- 1999-2003 3.8l - front valve cover
INSTALL: Simply pull on the hose to release the valve from the valve cover - pull the valve out of the hose. Insert new valve and push back into valve cover.
NOTES:
- The valve is in the end of 1/2" or so size hose inserted into a rubber grommet in the top of the valve cover
- If the valve checkball rattles, it's working
- Recommended replace interval - 40,000 miles
- The 'other' large tube going into the opposite valve cover is a breather tube
it should be on the valve pan cover with a hose running to air filter duct or MAF(mass air flow) the PCV recycles the blowback exhaust back into the engine .
The PVC valve is on the rear valve cover closer to the driver side of the car. It's easier to see and get to if you pull off the air cleaner housing which is a hassle but once you get it out of the way, you can get to the PVC valve easier. The problem is getting enough leverage to pull it loose from the connector which has a rigid pipe leading to it. It's a snug fit and you have to be able to get a good grip to pull the old one out of the hose. It's fairly easy to pull it loose from the valve cover.
What is necessary to replace a broken front tie-rod on a 1994 Pontiac Transport?
there are two tie rods on these vans. the inner and outer tie rods. if it is the inner itt is the long shaft type thing that goes right into the steering axle. the outer is where the grease fittings are and it attatches to the knuckle annd the inner tie rod. things that are necessary to do this are new parts, and there is a special tool that you need. they are available and most hardware stores such as Canadian tire to rent. after that you will need an alignment because it will be slightly off balance. when you unscrew the outer tie-rod from the inner tie-rod, count how many rotations you make so that when you but the new ones together it will be as close as possible so that you might not need an alignment.
How do you find a diagram on the location of the oxygen sensors for a 1999 Windstar?
its not a diagram but here are the locations and ID of all 4 o2 sensors There are 4 sensors on the windstars They are divided into 2 banks of 2, Bank one is the for the rear 3 cylinders of the engine, and bank two is for the front 3 cylinders. Bank one Sensor one(upstream sensor) is located on the exaust manafold on the back of the engine, to remove Had to bend part of the transmition heat shield out of the way. Bank one Sensor two (downstream sensor) is located just past the drivers side catilitic converter. Bank Two sensor one is located on the exaust manafold right at the front of the van, access is from the top. Bank two sensor two is located just past the passanger side catilitic converter. Note. before getting under the van, make sure to disconect the battary if you have the Air leveling suspension. And it is usualty a 7/8ths wrench/sloted deep socket that is needed.
the oxygen sensors are locate, one in front of the engine just look down between the space off the radiator and engine they all have a green clip. the second one is on the right front tire close to the oil filter, the 3 and 4 are under the van one between the manifold and the other in the tail pipe close to the engine.
What would cause a 1999 Windstar heater to blow hot air in the back but not in the front?
You probably have a faulty temp blend door motor assembly on the front unit. It is located directly behind the radio, way back in on the front of the heater case.
Could also be the door inside behind that assembly is broken. The door lifts to allow hot air and drops to close to send cold air. I am in the process of fixing mine and it aint pretty, but cheaper to get the assembly than to replace the door which requires the whole assembly to be replaced. Lots of luck with it.
What is the spark plug gap for a 1997 Infiniti QX4?
Your auto parts dealer can give you this information when you purchase your spark plugs. But a 1998 Infiniti QX4 gap is .041.
Where is the washer fluid reservoir for the rear window on the 1999 cougar?
the washer fluid resevoir is under the front right hand side wing of the car it feeds both front and rear screens the pipes do tend to fall off wich will in turn stop rear washer water also there is a rubber filter in the bottle wich blocks up as well, to get to bottle remove the 2 x 10mm bolts to the bottom of the inner arch(black plastic)pull to one side these and you will be able to get to the water bottle,to remove motor just pull towards center of car then remove rubber filter and clean ,2x elbo joints have nylon pipes check for them above pump this is normaley were they are these are push fit and 9times out of 10 the problem hope this helps
