Locks and Latches

Simply place a beveled block of wood in between the window and the door to make a gap about 3 inches in front of the hand lock. Then with a metal rod bent at 45 degrees just work it in there until you can find the right bar to pop up. You shouldn't have to work it around or down too far. This method worked on a 1998 F150.

Yes, it is legal for any citizen in the United States (and in all 50 states) to own and carry lock picks.

Yes, it's legal to carry a lock picking set in Missouri.

It's a device that you stick into the ignition of a car and it removes the entire console from the dashboard...it's meant for replacing ignitions if something gets stuck there or some other reason preventing you from using the ignition....ALTHOUGH some people use it to cripple cars for people as well, a more severe case of tire slashing when you think about it ... :)

I had the same problem once and took it to Firestone. They told me that you need to pull the level out really hard, don't worry it won't come out, and the hood should pop open. I wouldn't recommend this because yours might differ.

I would suggest the you remove the inner door panel to gain access to the lock. I believe that the plastic retainer that connects the lock to the catch is broken. In any case you will need to remove the inner door panel to determine the problem. The part is probably under a $1.00 but a hassel to get at..1930fcoupe

my remote central locking as just stoped working any ideas batt on key fob is new

locked car up at night next morning just wont open got to use key

A master key is an original operating key and operates all locks on a vehicle. Sometimes there are two keys, a master and a valet. The valet key is used when you drop off a car for someone else to park. A valet key will not open a trunk or glove box.

You probably don't need to change the pins, just the bushings (unless you let the bushings wear through to the pins). If you need to replace the pins (or bushings), first you need a stool or crate (to set the door on) or someone to help you, since the door is surprisingly heavy. Next, hammer a tap (or a Flathead screwdriver) onto the bottom of the pin until it is free (falls out). You may need a Flathead screwdriver or chisel to pry the bushings out of the hole Replace the pin and bushings. Check the pins for wear, and if there is none, put them back. It seems like an ordeal, but it is actually pretty mechanical and simple.

Do you want to know about a lock or a loch? And which one?

Very simple, have somebody pull on the release from inside either with the plastic lever or with a pair of pliers while you push up and down on the hood. It will jiggle loose. also pound on it with your fist

Try contacting an auto body shop or the dealership! If they can't help you, put an add in the paper or on line.

Another way is to remove the lock by taking out the screw even with the lock at the edge of the door. Install the lock in the reverse order. A locksmith can also do this.

call lock smith

One way is to:

1) disconnect the fuse for the power locks

2) press the power lock/unlock switch on the door panel, or keyless entry system as usual to operate the lock

3) the clicking sound is the power lock relay, which you can use to help locate it, although if it's under the dash, may still be difficult to find.

4) if there's no sound, then the relay is toast, and consulting a technical manual specific to your vehicle, or calling the dealer, is probably the only way

If the windows and the bottom two cig lighters dont work then its a blown fuse.

my Beretta is a 94 and it hood release is broke just the silver cable show ,,, i use needle nose pliers and pull it !

To replace lock cylinder in the hatch ,first inside hatch panel must be removed.

After removing the panel you will have access to the lock cylinder. Remove the linkage to

the cylinder and pull the retaining clip from the cylinder and the lock can be removed

from the outside of the latch. This is not a hard job to do , 1 hour max if your slow .

You have to drill the guts out of the ignition lock cylinder to remove the lock cylinder.A new lock cylinder will come with 2 keys. The original ignition switch itself is probably okay and reusable.

A Spider key is a homemade tool used mostly by shop lifters to disable certain electronic loss prevention devices stores put on their higher end items like the digital cameras and flat screen TV's at Wal-Mart. The key is made out of a credit card sized piece of wood or plastic with four small strong magnets glued on each corner in a specific pattern of "pulling" and "pushing" magnetic fields. The credit card sized key replicates the magnetic code the store uses to remove the security devices once the product has been purchased. These keys are technically not illegal but if you are caught with one inside a store you can expect a burglary tools misdemeanor charge and confiscation of the key at the least

HI IF THERE IS A HOLE FOR THE BARREL ITS A MANUALLY LOCKIN DOOR IF THERES NO HOLE ITS A CENTRAL LOCKING OPERATED DOOR SO YOU WOULD PROB HAVE TO PUT ALL YOUR WIRING/LOCK MECHANISM IN IT..................

Avulsion

Pull the inner door panel off and look inside the door and you will probably find a rod off the outside door handle.

Take something thin and bendable like a bobby pin or paperclip, put it in the key slot and twist until it kind of the shape of the key hole and when you hear a click turn the door and it should be unlocked. or take a hanger and put it in the side of the door and push it in and pull.