answersLogoWhite

0

Toyota 4Runner

The 4Runner is a mid-size sport utility vehicle (SUV) produced by Toyota Motor Corporation since 1984. This SUV is offered in four-wheel drive (4WD) and rear-wheel drive (RWD) layouts.

3,192 Questions

Is there a specific kind of antifreeze for a Toyota 4Runner?

yes,it can be purchased from the dealership. It is purple in color and has a lifetime warranty so if you use something else i believe Toyota can void the vehicals warranty if you used anything but genuine Toyota coolant when it comes to any problems relating to the cooling system.

What will cause the license plate lights to quit working on a 1995 Toyota 4Runner?

the bulbs could be out. if it has a trailer hitch on it and it was installed after market (not by the dealed), a lot of the time the marker lights to the trailer are spliced in to the licese plate lights and the type of conector that are used are prone to corosion. if that is the case just splice it together after the corroded wirer is remove and seal it electrical heat shrink.

What is a p0446 code on a 4Runner?

Trouble code P0446 means: Evaporative Emission System Vent Control Circuit

What causes a 1999 Harley Davidson EVO to keep running when you turn it off?

You could have carbon build up on the top of your pistons and heads. Try running a higher Octane gas and hotter spark plugs. Have your timing set with a light by somebody that knows how and use the correct gas. it can be caused by your timing being incorrectly set (pre ignition) this would also mean your bike isn't running to it's full potential, a golden rule is , don't play unless you're prepared for some roadside repairs , learn how on someone else's bike

How can you get your husbands car if his father wont give you the keys?

If your husband passed on leaving a Will and everything goes to you, then car is yours. The best thing to do is give a copy of the Will to your police department and they will escort you to be sure you get the keys to the car from your father-in-law. Good luck Marcy

I lost the only key to my 2003 Honda Civic how much will it cost to get a new key made?

try locksmith , will be around $100, Honda dealer will do it for about $170

Lost the only key for my 2002 Honda civic Honda charges $110.00 dollars for labor work, and 59.99 per key.

so yeah the $170 price range sounds about right. For the 2002 Honda this answer is right....but starting in 2003 Honda went to using a high security key blank which cost significantly more than the hd 106 keyblank used in the 2002 and earlier models....lost high security keys and the programming will run you about $250

How do you get back cover off to replace brake light on Toyota Previa 1998 automatic?

If it's the brake light in the boot lid then you have to take the cover off the inside of the boot lid and then you will have access to the light bulbs. If it's the brake light in the rear quarter panel then you open boot lid and unscrew the two bolts holding the light cluster and slide it backwards, then you will have access to the bulbs

Your 1991 4 runner will not stay crank and it loses power Also you have to start it with starter fluid what is wrong?

if you mean it doesnt crank long enough to start you probably need a battery. i suspect that the battery is dead because it takes so long to start. long crank times on these engines is usually caused by a bad cold start injector (found in the intake plenum on the passenger side, it has a small diameter steel fuel line and a 2 wire plug connected to it. held in place by 2 10mm screws) or the cold start injector time switch (found in the back of the engine behind the intake plenum, it sits in an aluminum casting that holds other water temp sensors and has a blue plug with 2 wires on it). replace these 2 items and you should be fine as far as hard starting goes.

What could be the problem when you turn your Toyota 4runner ac on nothing happens it doesn't come on there is no sound no air hot or cold blows out?

Check the fuse/relay. If good, then I'd say your blower went out. Be sure to check all wiring connections first though. Huge waste if all that might be wrong is a loose wiring harness or ground connection, or even a broken wire.

Change rear end gears on 1987 montecarlo ls?

It's not hard to do, but requires special tools and a great deal of knowledge (and/or experience). You'll need an install kit to properly 'set up' the gears. Many variations of kits exist, the biggest difference is whether or not the come with new bearings. Let the condition of your bearings or mileage be the deciding factor on replacing bearings. Some will tell you to just replace the bearings anyway - I suppose there is some merit to that. The gear set you'll need is from any 10 bolt 7.5 inch rear. GM put out millions of them. Do a search for GM 10 bolt 7.5 or 7.625 and you'll see the car that had them. Also, there are two different series carriers one for 3.23:1 gars and numeriaclly lower, and another series for 3.42:1 and up.

What is the problem in a 2001 Saturn SC1 if it clicks when you try to start it and it will not jump start?

The starter is probably at fault. Hit it with a hammer real good and if it starts it is the starter for sure. That won''t work but a few times.

On a 1990 Acura Integra RS is the crankshaft pulley bolt reverse thread?

No - The crankshaft bolt will loosen counter-clockwise. Because the crank bolt is so hard to remove it can seem as though it is reversed threaded. The crank turns the opposite direction that is used to tighten the bolt. For the crank bolt Lefty-Loosey (counter clockwise), Righty-Tighty (clockwise) apply here. The crank bolt is tightened to 87 ft/lbs of torque. It took more then 87 ft/lbs of torque to loosen my crank bolt. The manual says to apply a drop of motor oil when reinstalling the bolt. An Harmonic Balancer Pully Holding Tool is used to hold the crank while working with the crank bolt. Holding Tools can be found on the internet for $20 to $73. There are two sizes, 45 mm and 50 mm. For a 1990 model year the size is 50 mm. I made an Harmonic Balancer Pully Holding Tool by tack welding a 2 foot length of 1 1/2 inch by 1/2 inch piece of stock, for a handle, on a 2 inch (50 mm) hex nut. The nut fits into the pully to hold the crank and the socket, used to turn the crank bolt, fits through the nut.

How can you get the gas door open without using the cable?

Look in the trunk- there ought to be an emergency release- you might have to pull the trunk's liner back a bit to access this cable with a tab attached to it.

Where is the drier on the AC system of a 1995 Honda Civic 1493 engine?

the drier is located on the driver side next to the washer solvent bottle, you will have to remove the plastic fender well in order to access it.

Where is the starter relay switch located on a 1983 Oldsmobile Delta 88 And how do you change it.?

It's ontop the starter and has been for years and it's called the starter solenoid. You send 12 volts to it when you crank the car.

How can you disarm a Monitronics alarm?

Do you have a code? If not, go to page 16 of the owner's manual and you'll find the Installer's code (6-5-4-3-2-1) You enter that code with the door opened. The panel will talk to you and you can run through the system until it asks if you want to enter a security code. This talking alarm will walk you through the process. This will also let you add and delete contacts. In all cases, having the manual will help a lot. You can print an entire manual online.

How do you clear codes on 95 Dodge Intrepid 3.3 with out a code checker?

Codes will eventually clear on their own if the problem(s) no longer exist. If you can't wait disconnect the battery, reconnect after 30 minutes. The problem with this is you loose clock and radio settings.

Fuse location 2002 Mercedes Benz e320?

The 2002 Mercedes-Benz E320 fuse box is located in the engine compartment. The fuse box will be on the drivers side of the engine compartment.

What are the signs that the rotors in a 2000 Toyota 4runner need changing?

If you're changing the brake pads and there is too little rotor thikness to turn it, it should be replaced. If the rotor is warped and is too thin to be able to turn to remove the warping, replace it. If the brakes "pulsate" when you use moderate brake pressure, the rotor is warped.