Auto Parts and Repairs

If your 1987 Monte Carlo SS runs fine with poor gas in the carburetor but isn't getting fuel, the issue could be due to a clogged fuel filter or a failing fuel pump. Additionally, the carburetor itself might be dirty or have stuck float valves, preventing fuel from entering. It's also possible that there are air leaks in the intake manifold or vacuum lines affecting fuel delivery. Checking these components should help diagnose the problem.

To replace the slave cylinder on a 1990 Miata, first, locate the cylinder near the transmission and remove the retaining bolts. Disconnect the hydraulic line and remove the old slave cylinder. Install the new slave cylinder by reversing the removal process, ensuring all connections are secure. Finally, bleed the clutch system to remove any air before testing the clutch operation.

A car can stall with the clutch engaged while slowing down due to insufficient engine power or a lack of fuel reaching the engine. If the engine RPM drops too low, it may not maintain enough power to keep running, especially if the driver is not applying the throttle. Additionally, issues like a dirty fuel filter, malfunctioning idle air control valve, or a weak battery can contribute to stalling even with the clutch pressed.

To replace the alternator on a Dodge Caliber, start by disconnecting the negative battery terminal to prevent electrical shock. Remove any components obstructing access to the alternator, such as the air intake or battery tray, if necessary. Unbolt the alternator from its mounting bracket, disconnect the wiring harness, and take it out. Install the new alternator by reversing the steps: connect the wiring, secure it with bolts, and reassemble any removed components before reconnecting the battery.

To change the right lower ball joint on a 1993 Chevrolet Lumina 3.4, start by safely lifting the vehicle and removing the wheel. Disconnect the tie rod end and the lower control arm from the ball joint, then use a ball joint separator to detach the ball joint from the steering knuckle. Install the new ball joint, reattach the control arm and tie rod, and ensure all components are securely fastened before putting the wheel back on. Finally, lower the vehicle and perform a wheel alignment if necessary.

The flasher fuse on a 1999 Jeep Cherokee Sport is located in the fuse box, which is typically found under the dashboard on the driver's side. To access it, remove the cover of the fuse box, and look for the fuse labeled for the turn signals or hazard lights. The specific fuse position may vary, so it's advisable to consult the diagram on the inside of the fuse box cover for exact identification.

Yes, a bad knock sensor can cause hesitation upon acceleration in a 1996 Cougar. The knock sensor monitors engine knock and sends signals to the engine control unit (ECU) to adjust timing for optimal performance. If the sensor is faulty, it may lead to inappropriate timing adjustments, resulting in poor acceleration and hesitation. However, it's important to consider other potential causes, such as fuel delivery issues or ignition problems, before concluding that the knock sensor is the sole culprit.

The rear speakers in a 1998 Oldsmobile Cutlass are typically 6x9 inches. However, it's always a good idea to check the specific model and trim, as there can be variations. If you're considering replacing them, make sure to verify the dimensions and mounting depth for compatibility.

The recommended tire pressure for a Ford Mondeo Estate typically ranges between 30 to 35 psi (pounds per square inch) for both front and rear tires, depending on the specific model and load conditions. It's important to check the vehicle's owner manual or the sticker located on the driver's side door jamb for the exact specifications for your particular model. Always ensure tires are inflated when cold for the most accurate reading.

You can find the specifications for the timing and valve adjustment of a 2005 Yamaha Grizzly 80 in the owner's manual, which is often available for free online in PDF format. Additionally, forums and enthusiast websites dedicated to Yamaha ATVs may have shared this information. You can also check resources like YouTube for instructional videos that might include the necessary specs. Finally, websites like ATVServiceManuals.com often provide free or low-cost access to service manuals.

To remove the alternator from a 2004 Chevy Trailblazer, first disconnect the negative battery terminal to prevent electrical shorts. Then, remove the serpentine belt by releasing the tensioner and sliding the belt off the alternator pulley. Next, disconnect the electrical connectors from the alternator and remove the mounting bolts securing it to the engine. Finally, carefully lift the alternator out of its bracket.

The blue light on the dashboard of the Infiniti Q45 typically indicates that the engine is running in a cold state and is not yet at optimal operating temperature. This light serves as a reminder for the driver to allow the engine to warm up before driving aggressively. It can also indicate that the engine's coolant temperature is low, which is normal when starting the vehicle.

To change a headlight on a 1992 S-10, first, open the hood and locate the headlight assembly. Remove the retaining screws or clips that hold the assembly in place, then gently pull it out. Disconnect the electrical connector from the back of the headlight bulb and replace the old bulb with a new one, ensuring it’s securely connected. Finally, reassemble the headlight assembly and test the new bulb before closing the hood.

To remove the oil pan from a Volvo 940, first ensure the vehicle is safely raised and supported. Drain the engine oil and remove the oil filter. Then, detach any components obstructing the oil pan, such as the exhaust or crossmember, and remove the bolts securing the oil pan in place. Carefully pry the pan loose, being mindful of the gasket, and lift it off the engine.

In a 1993 Ford Ranger, the fuel pump typically has a wiring color code of a yellow wire for power and a black wire for ground. However, wire colors can vary depending on the specific model and configuration, so it's important to consult the vehicle's service manual or wiring diagram for accurate information. Always verify the wiring with a multimeter before making any connections.

To replace the horn button on a 2003 Chevy Malibu, first, disconnect the negative battery terminal to avoid any electrical issues. Then, remove the steering wheel airbag by unscrewing the retaining screws behind the steering wheel, carefully disconnect the airbag harness, and set it aside. Next, remove the steering wheel cover to access the horn button, which can be pulled out or unscrewed depending on the design. Finally, install the new horn button, reassemble the steering wheel components, and reconnect the battery.

The ABS and parking brake lights on a 2002 Chevy Trailblazer may stay on due to a malfunction in the ABS system, such as a faulty wheel speed sensor, or issues with the brake fluid level or the parking brake itself. If the parking brake is not fully released, it can trigger the light as well. Additionally, a problem with the ABS module or wiring could also cause these warning lights to remain illuminated. It's advisable to have the vehicle diagnosed using an OBD-II scanner for accurate troubleshooting.

To change the thermostat on a 2004 Nissan Sentra, you typically need a 10mm socket to remove the bolts securing the thermostat housing. Additionally, having a ratchet and extension can help reach the bolts more easily. Always make sure to consult your vehicle's manual for specific details or variations.

If your 1992 Camry LE V6 is experiencing a high shift point between first and second gear, it could be due to several factors, including low transmission fluid, a malfunctioning throttle position sensor, or issues with the transmission control module. It's also possible that the transmission itself may need adjustment or repair. Checking the transmission fluid level and condition should be the first step, followed by a diagnostic check for error codes. If the issue persists, consulting a professional mechanic is recommended.

To replace the intermediate shaft carrier bearing on a 2001 Ford Focus, first, lift the vehicle and remove the front wheels for better access. Disconnect the intermediate shaft from the transmission and then remove any necessary components to access the bearing assembly. Use a suitable tool to press out the old bearing and press in the new one, ensuring proper alignment. Finally, reassemble all components in reverse order, making sure everything is securely fastened.

The recommended tire pressure for a Fiat Fiorino typically ranges between 30 to 33 PSI (pounds per square inch) for the front tires and 28 to 32 PSI for the rear tires. However, it's best to consult the owner's manual or the tire pressure label located on the driver's side door jamb for the specific recommendation for your model and load conditions. Maintaining the correct tire pressure is essential for optimal performance and safety.

To replace the headlight switch on a 1992 Toyota Previa, first, disconnect the negative battery cable to ensure safety. Then, remove the dashboard panel surrounding the switch, typically by unscrewing or unclipping it. Next, detach the wiring harness from the old headlight switch, unscrew it from its mounting, and replace it with the new switch. Finally, reconnect the wiring harness, reassemble the dashboard panel, and reconnect the battery.

To reset the automatic windows on a 2004 Volvo XC90, start by fully closing the window you want to reset. Press and hold the window switch in the up position for a few seconds after it has closed completely. Then, press and hold the switch in the down position for a few seconds. This should recalibrate the window's automatic function. If the issue persists, you may need to repeat the process for each window.

ABS, or Anti-lock Braking System, is a safety feature in vehicles designed to prevent the wheels from locking up during hard braking. When you press the brakes, ABS automatically modulates brake pressure to maintain traction, allowing you to steer while braking. This helps prevent skidding and maintains control, especially on slippery surfaces. Overall, it enhances safety by improving braking performance in critical situations.

In a 1987 Chevy 350 fuel-injected engine, the ignition control module is typically located on the distributor. It is mounted on the side of the distributor housing, secured by screws. To access it, you may need to remove any surrounding components for better visibility and workspace. Always consult the vehicle's service manual for specific details related to your model.