0
Chevy Blazer S-10
The Chevy Blazer S-10 was a sport utility vehicle (SUV) produced by the American automaker General Motors Company from 1983 to 2005. This SUV was based on the design of the S-10 pickup and was manufactured in two generation models.
7,901 Questions
How do you change door hinge pins in a 2001 gmc jimmy?
You can't. The entire hinge must be replaced.
Completely FALSE! The pins can be replaced and are currently available for ~$6 from Advanced Auto Parts stores (Motormite #38419). First, the detent spring must be removed. Support the door either on a jack or some stands of the proper height. Remove the retention washer from the top of the pin. Then push the pin out of the hinge. Replace the bushings with those supplied in the replacement pin kit and push the new pin up into place the same way that the old one came out (make sure to lubricate the pin properly with some heavy grease). Install the retention washer and reinstall the spring (which is easier said than done).
Taking the spring out was hard and I've never been able to replace the old one. I here there is a special tool to do this but it is not that important to me. Be careful removing the old spring.
I have replaced the door hinge pins and bushings many time on my 99 Chevy blazer. You can buy the kit at autozone or most auto parts stores. My friend owns an autobody shop so he has the spring depresser tool to remove the detent spring. You may be able to buy the tool in an auto parts store or maybe even rent one. But if you can remove that spring just follow the directions above! Good luck!
The spring compressor tool is very cheap and runs about $10 at Advance or Auto Zone. Spend the little extra money to do the job right. Without it the door opens way too easily and is not held open. The best write up can be found here:
http://www.bodyshopzone.com/archives/mechanical/door/hinge/pin_replace_1.HTML
How do you refill a 1988 Chevy van with freon?
Unfortunately, if the air conditioning system is factory original and has not been converted to use the new R-134a refrigerant, you cannot refill the system yourself. R-12 refrigerant is the old stuff, it must be charged by a professional and will be very expensive. They quit making it almost 15 years ago. Depending on your location is could cost upwards of $300 to get it recharged, and if the system is low then you probably have a leak somewhere so that might be $300 out the proverbial window. If you plan on keeping the van, I would suggest that you convert the system to R-134a. A local air conditioning shop can do this for you. I will cost more than just a refill of R-12, but in the long run, it will be much cheaper as the refrigerant is MUCH less expensive should a leak develop.
How do you fill the rear window washer with fluid in a 1996 Jeep Cherokee low washer light is on?
Open the rear liftgate , above the left taillight lense you will see a rubber cap/plug , that is your fill point - I like to remove the plastic cover panel in the drivers rear of the cargo area so I can see the level of the washer fluid in the container
How do you remove the ignition lock cylinder from a 1994 Saturn sc2?
If it is like the '97 SC2, which it likely is:
Remove the plastic cover from around the steering column.
Turn the old ignition cylinder to ACC (I know what you are about to say... If you can turn the cylinder, why replace it. Unfortunately I can't answer that. I had to drill out the old lock to replace the one on my saturn. Please consult a locksmith before doing so. You don't want to drill into the wrong parts.)
With the old cylinder turned to ACC, there is a small button on the side (probably upper right towards the air vents) Push this button in and the old cylinder should pull out. Installation is reverse of removal (without the drilling...)
Where is the Daytime Running Light Module specifically located for a 1994 Jeep Grand Cherokee?
The Daytime Running Lights module (DRL) is located behind and below the radio in all Gen 1 Neons (at least the Canadian versions). Remove the console faceplate by just pulling it off. Remove the Radio with a 10 mm socket. You may be able to continue without unplugging the radio, but it's easier to access if you do.
The DRL is bolted on an angle to the lower rear of where the radio sits. Two 10 mm bolts also hold it in place, you will be easily able to see the left hand one.. the right will be more difficult. Both can be accessed by inserting your 10 mm socket on and extension through the bolt access holes under the radio housing. Be careful not to lose the bolts when you've released them, as fishing them out from the shifter console will be annoying at best!
The DRL is connected by one large rectangular connector... it just unclips and pulls off. You will lose your daytime running lights and High Beam indicator once removed, however all other headlight functions will remain.
Firing order diagram for a 96 jeep 4.0 6 cylinder?
its 1-5-3-6-2-4 Clockwise on the distributor, #1 is at the front of the engine.
Where is the 4x4 switch on a 89 S10 blazer the front axle wont engage in 4x4?
there is a vacum actuator located on the passenger side of the vehicle.checck the vacum hose to make sure it is getting vacum when you enguage the switch or gear shifter.this has a cable that goes to the front difererential that acuates to engage the front diferential.the vacume hose may come loose.or the cable pulled out of the holder that connects to the acuator.
My 93 blazer has a vacum line behind the intake in front of the dis. it fell apart 4X4 stopped working i just replaced it it worked great 1993 4.3W
How to tell if head gasket blown?
It really depends on how bad the problem is. If the problem is a small leak in the head gasket or head, then the engine will start and may even run ok for a little bit before it starts overheating. If the leak is bad enough a good deal of antifreeze might be inside the engine and starting it could result in severe damage (this is called hydrolock), and you will likely need another engine if this happens. No matter if you can start it or not, it is strongly recommended that you minimize any driving in it and get it fixed as soon as possible.
How do you replace a fuel pump on a 1996 Chevy blazer 4x4?
1) If fuel tank is full you will need to siphon fuel out 2) Remove any type of skid plate or cover from fuel tank. 3) Disconnect fuel fill tube, wiring harness, and fuel lines from fuel tank. 4) Support fuel tank and remove hold down bolts(or nuts) for fuel tank strap. 5) Lower fuel tank to ground. NOTE: You may need to remove driveline on some vehicles to have room to get tank out. 6) Use brass punch to unscrew fuel pump locking plate on top of fuel tank. 7)Remove and replace fuel pump from tank and reassemble everything the same way you took it apart.
How do you replace the front and rear brakes on a 2001 VW Beetle?
You will need a metric Allen wrench (7 mm).Jack up passenger side and place jack stand. Remove wheel. Take a screwdriver and work it in between brake pad and rotor. Once done, apply steady pressure on brake pad until you push the caliper piston as far in (toward engine) as it will go. You will need to remove caliper bolts. They are on the back of the caliper at top and bottom. Place Allen wrench in each bolt and turn wrench towards front of vehicle to remove. Once removed, remove caliper with brake pads inside. Match new brake pads with old and put new pads in like you removed the old pads. Place new pads and caliper back on vehicle and replace caliper bolts. If caliper and new pads do not slide easily back in place,you may need to get a large c-clamp and push piston back in caliper a little more. After you get caliper back on and tightened, get in car and pump your brake pedal until it is hard to push. This resets the brake pads. Replace wheel and your done!!
How do you replace outside door handle 2000 mountaineer?
To install an exterior door handle on a Cherokee Jeep, first remove the window crank handle and the three screws in the inner door trim panel. Second, remove the inner door panel from the door using a trim stick and take off the vapor barrier inside the door. Third, remove the nut on the rear of the door handle, position the exterior door handle, and secure in place.
How do you put on the 4 wheel drive?
first you need to lock the front hubs (this is done manually) you must rotate the hubs located on the two front wheels. On stock hubs, it'll say 4x... 2 (on the rim of the hub) when not engaged and 4x...4 when engaged. to lock then pull the short stick shift down that hi 4 then down again to low 4 range to disengage push up then unlock hubs rule of thumb always reverse back 20ft to ensure full release ...... agree... however, make sure you are rolling about 2-3 mph forward... this will help engage. I just read it in my 1986 cj7 manual today.
Type of fluid in 1999 silverado transfer case?
it uses a brand by acdelco, and you have to order it from a dealer. its called auto trak 2. if you don't use this specific fluid it will mess up your transfer case, i learned the hard way. and they wont recomend it until you've already had problems , that's how they make their money, good luck, it runs about 6-10 dollars a quart.
Brake lights wont turn off on Honda civic?
Did you replace the bulbs recently? if so make sure you have a dual filament bulb. If you put a single filament bulb in it will cause this to happen.
If the bulb isn't the issue then you should take it to a mechanic to see if there is a sensor out of whack that is tellling the brake lights to come on.
Attach a flexible tube to the bleeder screw at the top of the wheel cylinder(caliper) of the affected wheel Put the other end of this hose into a container filled with clean brake fluid Have an assistant push the brake pedal down approx. 2/3 of its travel
Open the bleeder screw
Observe the hose in the container for air bubbles
Close bleeder screw
Repeat until no air bubbles are observed in container MAKE SURE MASTER CYLINDER DOES NOT EMPTY DURING THIS PROCEDURE
It could be the p/s leaaking if you are loosing fluid. Otherwise, you just have to get back there and see what is leaking.
How can you fix a broken relationship if you and your partner has problems?
clearly the boy and the girl needs to find a day to talk it all over. They both need to listen to each other and should talk it out and they should solve it together. Talk calmly and don't use irritated voice, cuz arguing won't solve anything. If your the boy or da girl, you should see the point of view of you bf/gf.
If a car is abandon on your property for over 2 years how do you get a title?
The Laws vary from State to State. However You are usually required to take it and have it inspected by the state patrol to assure it is safe for use and then apply for a salvage title.
How do you choose a vacuum pump is not affected by high humidity?
When selecting a vacuum pump that's unaffected by high humidity, focus on pumps with corrosion-resistant materials, such as stainless steel. Consider oil-free or dry pumps, as they're less susceptible to moisture-related issues. Additionally, look for pumps with proper sealing mechanisms and moisture removal systems to ensure optimal performance in humid environments. Regular maintenance and monitoring of humidity levels are also essential to prolong the pump's lifespan.
How many catalytic converter does a 2002 Chevy Blazer have?
There are two under the car, one is right inder the front passanger and another one that is right under the back seat.on the right side.
How do you check fuel pressure on a 96 blazer?
there is a port on the fuel rail going to the throttle body...remove your air cleaner and hook your guage to it...start the engine...monitor the guage
What is thetowing capacity for a puegeot 307hdi?
Hi,
No Gross Vehicular Weight (GVW) is given in stats., but towing capacity is a maximum 1,360kg braked. This is a highly respectable tow weight for a diesel vehicle. Hope this helps.
Can you flat tow a 2009 Caliber w CVT II Trans?
No. Only the 5-spd models can be flat towed, all others will suffer transmission damage.
