answersLogoWhite

0

🚗

Chevy Blazer S-10

The Chevy Blazer S-10 was a sport utility vehicle (SUV) produced by the American automaker General Motors Company from 1983 to 2005. This SUV was based on the design of the S-10 pickup and was manufactured in two generation models.

7,901 Questions

How do you replace a 1993 Chevy s-10 blazer ignition lock cylinder?

Start by pulling the horn button off of the steering wheel, just grab it and pull, you'll see a big nut in the middle you will need to remove it and at this point you will need a wheel puller to remove steering wheel, probaly can rent or borrow one. Then it's a screw that holds the turn signal in place, pay attention how it goes and remove, next remove the screws holding the turn signal assembly in place. You'll have to wiggle it around to get the 4 way flasher button to come out with the assembly, leaving the wires intact just pull to the side out of your way. Now theres a outside snap ring around the splined shaft below where the big nut was, very hard to see it helps if you have someone to push down on the steering wheel lock disc, that's the black disc with teeth around the outside. Once you get the snap ring off the disc will pull off also, At this point put key in OFF position and remove the last screw behind where disc was, should be in the upper right. This screw holds the lock cylinder in place it is longer than the others. Now gently pry the lock cylinder out, Don't move anything inside of steering coulum until you get new cylinder back in place. Then just reverse what you did to put it back together. I will admit snap ring is tough to remove, but process is kinda simple. On a scale of 1 - 10, i'd rate it a 4. Hope this helps..

How do you replace the catalytic converter on a 1999 s10 blazer?

You may be able to get a direct replacement at the auto parts store, but actually separating the pieces of the exhaust is quite a chore, as they tend to bond together with corrosion/rust. Cutting and welding is often necessary. Taking it to a reputable shop may be a good idea.

Where is the horn located on a 2001 Chevy silverado ext cab?

There are two horns, One is below each turn signal. The passenger side can be gotten at from below easily. A 10mm wrench is all you need. The D/S horn is harder to get at. You may have to pull the turn light housing. It just pulls out. Squeeze the plastic clip at the outside end and pull. I know all this because I just did it on mine. The P/S horn is dead. Now I just need to find a reasonable price for another one.

Why does your 86 K5 Blazer spit sputter and backfire when you accelerate?

There could be condensation in the distributor or possibly a worn camshaft. It is also possible that the carberatuer needs to be cleaned or rebuilt.

What causes gas fumes in the radiator?

In most cases is is blown head gasket. The engine suckes air through the hole in the gasket and sends it to cooling system. You never know how long it gonna last.

Can also be caused by a defective pressure relief valve in the coolant reservoir cap. If it is the head gasket, you may also find you can smell combustion gases in the coolant. These won't smell the same as the exhaust gas though as the exhaust has been through the catalytic converter. If changing the cap fails to cure the problem, disconnect and isolate the ht leads or coil low tension wires and remove the pressure cap from the coolant tank. Get someone to turn the engine over on the starter motor while you look into the tank. If you see bubbles emerging in the coolant, it's probably the head gasket.

And a worse case scenario, a cracked head is possible.

How do you check ignition switch in a 1998 Toyota 4-Runner?

I have the same problem, going to have a locksmith make sure its the ignition switch and cylinder and just not a key problem or a tumbler problem.

Where is the throttle position sensor located on a 1994 buick skylark?

it is located behind the ignition control module which is where your coil packs are mounted and your spark plug wires are connected. u cant see it u must remove the base plate and it is mounted to it. sticks through the engine block has o-ring.

Why is your 2002 jeep wrangler squeeling in cold weather at start up?

Check the fan belt it may be tight when cold and causes the whistle until it loosends up when it warms up during use. Can also be caused by the throttle body needing to be cleaned, carbon build up on the IAC motor

How do you set the radio stations on a 1997 Chevy Blazer?

Select the station you want to save. Push and hold the #1 button for a few seconds. The station will be set to the #1 button. Continue to your next station selection then push and hold #2 button and so on.

Where is the throttle position sensor located on a 1994 Cadillac Eldorado?

Remove the air cleaner and the air supply from the top of the throttle body. Have someone step inside the vehicle and slowly press and release the throttle while the engine is off. Watch to see what moves. The throttle butterfly is operated by the cable from the accelerator pedal. Notice that the cable goes over a sprocket that moves the throttle. On the OPPOSITE side of the throttle body should be a black plastic thingy with wires connected. THAT's the throttle body.

Where can you get the serpentine belt diagram for a 1991 Ford Bronco EFI 5.0?

most auto parts store carry manuels on most cars just find the one that is on your van and a diagram of how the belts go on will be in it. the books cost around 15 dollars to buy but some store will let you look at them.

Why would the brakes on the rear-passenger wheel make a grinding metal-on-metal noise but continue to function properly?

there is a little metal plate that scrapes the rotor to warn you when your pads are getting too warn down True, if you have rear disc brakes. But if, like most cars built before 2000 and many cars built since, you have rear drum brakes, you probably have a loose spring or something of the like. Drum brakes have springs and cables to hold the shoes in position. If a spring snaps, the shoes will be off center in the drum, causing a grinding sound. They may still work like always. Also important is that rear brakes do only 25% of the work. It's possible that the shoes need to be replaced and the drums turned or replaced even if you are able to stop with no problem. Ignoring a problem with brakes will end up costing a whole lot more money in the long run.

Where is the Crank sensor on 1999 blazer 4.3?

If you want to do it yourself procure the Haynes Manual for your unit. Part number 24046 '90-94.: There may be a couple of sensors, the procedure below is for the 24x sensor if fitted. remove the drive belt. raise the car and support on jackstands remove the crankshaft pulley remove the bolt and the sensor wiring harness bracket. Note well the routing of the wiring as you must replace it as installed at the factory. remove the sensor mounting bolts and pull the wiring harness. reverse the procedure to install. After disturbing the seensor the crankshaft variation relearn procedure may be required. If the engine MIL light illuminates take it to a dealer and get them to reset the system for you. To replace the 7x sensor, disconnect the wire, remove the bolt holding the sensor in th eblock and withdraw the sensor. make sure you replace the O-ring after lubing it with engine oil.

How do you remove a radio from a 97 s10 blazer?

Answer from J @ floridaproweb.comThe bezel surrounding the radio is a solid bezel that also trims out around the speedo and light switch.

A Phillips head screw driver and small socket will be needed to remove the dash panels. I also like to use a small pick tool that looks like a little hook to place behind the the dash panels and gentle pull the panel away from the clipped areas.

You must be careful to have removed ALL screws of each panel you are removing otherwise you will break/damage your dash.

First start by removing the screw near the cigarette lighter (to the left of the cigarette lighter).

You will need to remove the drivers side lower dash panel before you can completely remove the bezel surrounding the stereo and speedometer... because it overlaps the upper dash trim. Once you remove the bottom dash trim you can remove the 2 remaining screws from the upper bezel.

You must put the vehicle in the lowest gear position for the dash panel to clear the shifter when removing. REMEMBER to unplug all wiring harnesses and don't yank or pull to forcefully on anything... if it seems stuck then either a screw was left in tact or a wiring harness is still connected to a switch mounted in the dash panel.

Once removed you can clearly see the screws to remove the factory stereo... You must have an install kit that contains the GM wiring harness adapter otherwise you will loose some nice factory features. The wiring harness can be found at Circuit City or Best Buy!

Good Luck!

Why do my blinkers blink too fast and my rear brake lights not work?

That bulb is burnt out. When the circuit is not completed like with a blown bulb, the flasher unit will blink faster to let the driver know something is wrong with that side. It should only be faster with the side that is burnt out.

Where is the engine coolant sensor in a 1998 Saturn SC1?

Does this use a 2.2L Ecotec engine? If so,the #1 ign. coil and #1 spark plug are used in combination to provide the functionality of a camshaft position sensor. Often, a worn spark plug can set a code if that's why you're looking for the sensor.

If your 1996 ford windstar cranks but won't start what could be the problem?

I hear that the problem is the pressure to the fuel pump. Also have heard that the alternator is the problem. To be honest, I cannot figure out why mine will not start either. I have replaced the fuel filter, O2 sensors, thermostat, reset the inertia switch, and spark plugs and wires.... nothing has worked yet.

I have had the same problem, 2cd Explorer. I replaced the fuel relay. No problems now

Where is the starter solenoid located on a 94 grand marquis?

on a 92 it's drivers side, mounted on wheelwell, if you goto autozone.com and log in your info, then go to component locations that will tell you where all your relays are located, very well-informed a-z easy searching

The speedometer started bouncing and the transmission wont up shift on 1998 civic lx?

Its hard to say without you posting the year,make,model,engine,etc. But just guessing yes it could. on a lot of newer vehicles, the transmission needs to know how fast the car is going. This is one of 2 things the transmission needs know before it can function properly. The other is engine load.

Where is the starter located on a 1989 Chevy S-10?

It's on the bottom of the engine, where the engine joins the transaxle. If memory serves correctly, simply remove the wires and the three bolts holding the starter in place and reverse that order to replace it. It's also important to note, that when doing any work with electrical parts on a car, always disconnect the negative battery terminal to avoid accidental grounding.

Where is the horn in a 1994 Opel Astra located in the engine?

It is located under the front bumper in the left hand corner.It can be seen from under in the front left corner.

1998 Chevy blazer radio wont work?

The problem is most likely a broken blend door. This problem is very common on this model and that's always a pretty good guess. There is an aftermarket fix for the problem or have the dealer diagnose and fix it for close to $1k.

Trending Questions
What could be wrong if the car wont start after a rollover? Is there any difference between drive shaft in extend cab 1998 S-10 and regular cab 2 part shaft 4cyl 5 speed manual? How do you fix the gas gauge on your 94 Explorer? Will a rear end from a 2000 2wd Chevy s10 fit a 1999 4wd Chevy s10? How did the plow revolutionized farming and increased production? Why wont 2000 blazer come out of 4wd? What is the speaker size in a 1998 4 door Chevy blazer? How do you reset your airbag light on a 2002 maxima? Where is the fuel pump relay located in your 1988 Chevy truck? Where can you find a serpentine diagram for a ford f150? What can cause gas and temperature gauge to stop working? 95 intrepid 3.3literRuns super rich once in a while not the map sensor or cam sensor....fuel pressure kinda high 55 lbs. dash also goes outtach speedo etc? How do you change a heater core in a 1996 S-10 Blazer? Where is the Crank sensor on 1999 blazer 4.3? What is wrong with 1989 RS 2.8 Camaro if you replaced the fuel pump and it runs for 3 seconds and cuts out and you have no fuel pressure and only 6 volts are going to the pump? Is there a easy way to install starter on 95 blazer? How do you replace the window latch on a 1988 Chevy blazer K5? 2000 S10 Blazer will crank but will not start? Why would a 1990 Chevy Blazer blow white smoke with a strong smell after coming to a stop and resuming after driving downhill from a mountain? Why doesn't the brake lights work on a 2000 Buick Lasabre when the fuse is good?