0
Pulleys
A pulley is a mechanism composed of a wheel on an axle or shaft. A rope, or cable usually runs over the wheel and inside the groove. Pulleys are normally used to change the direction of an applied force to make the work easier. It is one of the six simple machines.
1,797 Questions
How do you know if the belt tensioner and idler pulley are bad on 97 GP GPT?
First thing, if your belt seems soft or sloppy when you push on it or if it bounces at an idle. When you start/drive you will get a slight knocking sound between 900-1200 RPM that's the internal spring on the tensioner. To fix this you have to go to a dealer and get the replacement supercharger tensioner. The main tensioner in the back near the firewall is easy to find at auto zone or o'reilly auto parts. The idler pulley is a lot easyer to check. Take your accessory belt off of the idler pulley and try to move it, if theres ANY slop it needs to be replaced.
Which is The name of the muscle that helps us to lift things over the head?
The Deltoid Muscle It's the Deltoid muscle maybe the triceps
Where is the tension pulley at on a 97 Sunfire?
On my '96, it's located on the passenger side of the engine, back and down from
the alternator. It will be very shiny and doesn't look quite like the other pulleys. It's the only
one that contacts the back, or outside, of the belt.
yes. it is a dummy pulley, its purpuse is to kep the belt in place and tight. ==answer no it should not turn at all if installed and belt is on it if belt is not in place, yes it will spin freely
How do you change the belt tensioner pulley on your 1994 Astro van?
On the majority of vehicles, the alternator has a mounting bolt that can be loosened and then you move the alternator out away from the belt ; thus applying more tension. This tightens the belt, then while holding it in the new position , re-tighten the mounting bolt.
How do you remove the tension pulley on the 1993 Seville 4.6L Northstar engine?
Not easily. Get a manual on your car.
I had the same problem, the worn out tensioner belt pulley was never replaced and although everything seemed fine for several miles, the timing belt would walk off gears. Check all pulleys and bearings associated with the timing belt. This is a real chore so don't have your car serviced by mechanics who may be too busy to replace all parts contained in the replacement kit. A full timing belt replacement kit is very important with this vehicle.
1997 jetta stalling and rough idling?
Hello, 1st thing it sounds like it needs a tune up. Change the spark plugs, plug wires, distributer cap and rotter button. If this does not help, you might want to take your vehicle to the shop. Could be the fuel injectors are stopping up. If you havn't had your car tuned up in some time then that's probably the problem. Hope this helps.
*i shall add to the previous answer that you might want to check your MAS. mine had a similar issue and after much trial and error it turned out this was the problem. a tune up never hurts though ... hope this helped :D
What is a tension pulley on a Pontiac Sunfire 2.2 L Engine?
tension pulley is an automatic tensioner that keeps the serpentine belt at the proper tension it is a single pulley that is smooth (no grooves) usually turning clockwise with constant pressure loosens pulley for belt removal use caution pulley is spring loaded
How do you fit the drive belt on an ef falcon there are a lot of pulleys. What is the configuration?
hi there. on the underside of your bonnet there should be a diagram of the belt configuration and how to install the belt. do you have a manufacturers manual in the glove box?
Mazda mx3 crankshaft pulley removal?
Loosen the 17mm bolt in the middle of the pulley. Loosen the belt tensioner, and the pulley should slide off with a little help. Make sure to nothing the little key-way that lines the pulley up.
What does the crank shaft pulley do on a 1994 Honda accord ex?
it drives the serpentine belt for your accesories like AC, power steering, and alternator.
The crankshaft pulley also serves as a harmonic balancer in some cars. It means that the pulley helps to dampen engine vibrations that arise during/between the power strokes especially in diesel engines. When the pulley is aged you will experience engine vibrations accompanied with sone kind of whining noise around the belt area of the engine.
Where is the crank pulley located on 91 civic dx?
Where is the crank pulley located on a 1991 honda civic dx
How do you change the idler pulley on a 1994 explorer?
On the belt routing diagram under the hood (near the grille, but under the hood) you will find the location of the 'tensioner' pulley. You need to get a 15mm socket and place it on the bolt on the tensioner pulley. Then use a ratchet to put clockwise pressure on the bolt to loosen the tension on the belt. This will allow you to remove the belt from the idler pulley, remove the bolt, put on the new pulley. Now put clockwise pressure on the tensioner pulley again to put slack in the belt so you can slip it around the new idler pulley. You're done.
Is there a diagram for how to install a power steering pump in a 1971 GTO?
You can find the diagram in a 1976 Motor Guide. You should be able to pick one up on eBay for about 15 bucks.
How do you replace the alternator on a 2002 Mazda Protege LX?
Remove the cruise control diaphragm and take it out of the way to gain access from the top. Disconnect the battery negative to prevent shorts. Go in from underneath and take to finish the rest of the job. Disconnect the exhaust pipe donut connection and slide back the catback exhaust to buy room where u could slipe the alternator out from underneath. Gonna have to disconnect the muffler hangers; theres four of them. Then its taking the step in reverse and put together time.
Where to find crankshaft pulley bolt for 1.5 DX Honda Civic?
At a Honda dealer for $10. If one is not within driving distance, then go to Honda.com.
Does the idler pulley cause rough idling?
No. The idler pulley only maintains tension on the serpentine belt. A faulty idler pulley can cause noise and a loose tensioner arm can cause belt slipping but other than having a similar name, it has nothing in common with engine idling.
How to Measure the size of a supercharger pulley?
Every manufacture measures it differently. Some will take the inter-rib and measure it to the other inter-rib. Others might take the outer-rib to outer-rib. Vortech, Paxton, Eaton all do inter-rib to inter-rib. Thank you, From www.SuperchargersOnline.com
How do you replace the idler pulley assembly in a 1993 Plymouth Voyager?
you have to do this from under the van. jack the vechicle up and be sure to support it on jack stands for `safety. right behind the pulley ia a 15 mm bolt this bolt is the only bolty that holds the pully on. it is harde to get to a person with small hand has little or less problems.
How do you mount the Pulley to a Power Steering Pump on a 1989 Lincoln Continental Signature?
there is a special tool that you use to put it on, your local checker or auto store should have one.
Yes, they can, but generally if subject to abuse. The main problems are cracks and coming loose from the shaft.
How do you remove the nut on the crankshaft pulley on 1998 mercury villager?
1. Large air impact wrench.
2. Fabricate or buy holding tool to keep pulley from turning while you remove nut.
How do you remove a crankshaft pulley bolt from 1997 Isuzu rodeo?
Take out number one spark plug (or all to make it easier to turn) fit a socket to crank pulley bolt and turn the crank until it's just after TDC say thirty degrees. Feed about 900mm of 10mm rope into number one cylinder but don't drop it all the way in. Turn the crank back until you get a firm resistance and apply a breaker bar to the socket. Apply pressure to the breaker bar until the bolt undoes. You will probably need to remove the radiator and fan assembly to be able to get to the crank pulley unless you have already done so.
