Ford Windstar LX

on the cover of the timing belt

The reason a high beam indicator light might remain on in the dash of a 2005 Nissan Sentra might be a short in the wiring for the high beam headlights. It could also mean a short in the wiring of the steering wheel where the high beam switch is located.

Could it be the hazard lights?

It's absoultly NOT the hazard lights. It is some kind of warning indicator. In my van (2003 Toyota Sienna) it is beside the ABS indicator, and besides that, the hazard lights are facing away from each other. If anyone has an owner's manuel please look. I've lost mine.

I have the manual but its in Japanese from which I cant understand a word. Its number 17 in the list of lights that's all I see. I also have this problem.It started yesterday and I have no clue how to fix it. It goes off sometimes and comes on after a while. Could it have anything t5o do with the temperature? Its been cold lately (2degrees).....I agree with the person below...My Toyota sprinter has the same light and it was the tire pressure...i refilled the air in all and found 1 was extremely low....all fixed now:)

I found my answer. I have the 2003 Sienna. The indicator is a tire pressure light. There was a nail found in a tire. The nail was removed, the tire was patched the light is now off.

.032 is the gap

gap is .035

o.6

it depend on the Spark-plug if it's a singel electrod, the gap should be 0.9 mm. by a dubble electrod ther should be a gap of about 0.6mm each best regards tom

No it becomes an Erect Penis

You might try the HAYNES manual

The replacement of a MAF sensor will be different for vehicle models and brands. The MAF sensor bolts onto most engines, and is easy to change.

I went to our town ford dealership and they made me a copy from the manuals they had in the basement of the dealership. Price: One dozen donuts

Transmission problem. Take it to a professional.

Should be .035

i have recently encountered this on my 2002 GMC Envoy. After removing many of the underdash parts, ie, shroud under the dashboard, and some of the plastic vent ducts i identified the source of the sound. There are three separate actuator motors that help to control which vents the air comes out of, ie defroster, dashboard vents, or foot vents or some combination therof. One of the actuator motors is causing the clicking sound. Unfortuantely, you can only change the lower actuator motor from the bottom, the other two SEEM to have to be accessed by removing the dashboard and/or center control panel. I am currently researching this to perform the repair myself, because a trip to the dealer is certainly not going to be inexpensive.

I recently changed the E.G.R. valve on my 1990 Dodge Spirit 2.5L (non-turbo). Now it is quiet @ idle & starts right up. I also notice an improvement in the gas mileage. Good Luck.

fuse #14 under the steering column

on my 03 discovery there is a sticker under the hood on top of the grille

This is listed in the owners manual and on a placard under the hood. Also any auto parts store can provide this info.

Should be .050 inches.

Depends on the year, make, and model vehicle is it installed in.

I just put a new engine in my 91 Toyota and decided to paint everything being it was all apart. If you have acces to a compressor and inpact tools that will be all you need, but if you don't the only other way that I know of is to use a old fan belt, put it on the pully and make a tight loop, clamp the loop with a pair of vice grips to keep it tight. Put your wratchet on and hit the wratchet sharply with a hammer. I hope this helps you.

I just put a new engine in my 91 Toyota and decided to paint everything being it was all apart. If you have acces to a compressor and inpact tools that will be all you need, but if you don't the only other way that I know of is to use a old fan belt, put it on the pully and make a tight loop, clamp the loop with a pair of vice grips to keep it tight. Put your wratchet on and hit the wratchet sharply with a hammer. I hope this helps you.

9300lbs Gross Vehicle Weight Rating....Van, plus any cargo and passengers

Replacement of your window you will have to remove door panel. You will need a door panel tool or a paint scrapper like tool. You will have to remove some screws around door handle and so. Then you will need to remove door panel by prying door loss around the edges of the door panel. You will see some bolts on the window track remove and replace window, vacuum broken glass if any. When done with the repairs or anything your doing after removing door panel. Then the door push-pins are supposed to be on the door panel. When ready to install those push-pins are inserted inside the door holes. Push them in until you hear a click. After that reinstall the door handle and screws. exc.

I believe the descriptor is: Evap Low Pressure (related to fuel tank)

Spark Plug Gap = 0.060 for both S-10 & Trailblazer vehicles 1996-2005.