0
1995-2005 Chevy Cavaliers
The 1995-2005 Chevy Cavalier was the third generation Cavalier model produced by General Motors. In 1996, the Cavalier Z24 received the new LD9 2.4 liter engine along with the Getrag F23 5-speed manual transmission.
7,016 Questions
It means your traction control is turned off. Should be a button for it on the side of your shifter.
How do i start my astro van when the key will not turn in the ignition?
get a new key or break ignition with flathead screwdriver or try wiggling old ket around
Appended Aug. 7th, 2010: Possible pass-lock failure. this is a switch that is part of the ignition switch, and must be replaced with the whole ignition switch.
How do you set the timing on a 1998 2.2 liter?
you have to pull your timing cover off and line up the timing marks on the cam gear and the crank gear auto zone.com has all the info on how to do it
How do you remove shift knob on intrigue?
At the bottom of the knob where it meets the shaft, on the side towards the dash, there is a pin which is shaped like a staple.
Use a small screwdriver to pry the pin out towards the dash, then pull the knob up while twisting it slightly back and forth.
Why does 1997 Mazda familia with spark plug and fuel pump in good condition but won't start?
There can be 101 problems with your car. Does your battery have a charge? Please be more descriptive if you can.
How do you open a jammed drain plug on a 1995 Nissan Quest to do antifreeze flushing?
there are other ways of flushing the antifreeze out besides the drain plug if the drain plug is jammed. for instance, loosen the clamp on the hose at the bottom of the radiator and pull the hose off. make sure to have a bucket or something large enough to catch all the fluid but small enough to fit under your vehicle. and watch out! it comes out fast!
How do you get to the turn signal flasher on a 1997 GMC Jimmy to replace it?
answer: i just did it today 4/10/08 you have to remove about 10 screws you need a torque wrench set and a 7mm. socket . remove or just loosen up the 2 or 3 bottom panels underneath the steering column the signal relay and hazard relay are right next to each other next to the cigarette lighter housing but behind the panels that you have to remove . i pulled it out with a needle nose plyers. not bad it took me 30 min. or less the relay was $10 at the dealer . i hope this helped you...
Where is the horn relay on a 95 Grand Am?
The fuse box in the engine compartment take the lid off turn the cover over it should have a diagram of the relay for the horn. the Relay is in the fuse box. I believe the fuse box is on the driver side under the
How do you replace the front wheel hub assembly on a 2004 Oldsmobile Alero?
You will need to buy a new wheel hub assembly from your local auto parts store. you will also need a 36 mm socket in additional to the usual tools. I also found that a wheel puller is helpful(but not necessary) you should be able to rent one from your local auto parts store for a refundable deposit.
Take off the wheel.
Remove all break components.
remove 36 mm axle nut.
remove the 3 bolts holding the hub on and unplug the wires from it.
here is where I used the wheel puller to take off the hub. You may be able to remove it using a hammer. (A wheel puller is a lot easier.)
Put the new one on and reconnect everything.
Keep these directions handy so you can do it again next time the bearings go out.
yes, the shift linkage has a switch to only allow the car to start in either park, or neutral. All automatic transmissions have a neutral safety switch. It is misadjusted or defective.
How do you remove the shift knob on a 2002 Altima SE?
i have the same car you just have to turn it to your left
How do you replace the front turn signal light bulb on a 1996 Saturn SC2?
rear you use a torx driver to remove taillight assembly screws. them replace bulb.
there is a sensor in the bottom of the coolant bottle, change this and you should be o.k. tap the sensor with a screw driver it will go out uts just stuck
95 aurora leaking oil a lot in right front in front of motor any ideas?
Engine seal, valve cover gaskets, timing chain cover, oil sending unit, bad oil filter I had the same problem and it turned out to be the oil cooler hoses going to the radiator from the oil filter--after I had spent some bucks doing other things to it !! They were leaking at the swedged fittings.
What would cause only one side of the power seat in a car to move?
Apparently the seat has either a defective or broken part or something is jamming the side that wont move. Only way to really know is to get someone quailified to take a look at it and go from there. , EzForJesus
The thermostat you installed was either bad or is installed upside down. Possibly a clogged heater core. Possibly the system needs bleeding.
AnswerCould be your control cable is broken. Not familiar with your particular model but look for a cable on or near the firewall near the heater core. You may be able to move it by hand and get the haet you need. AnswerRemove DEX coolant the manufacturer recommends. DEX clogs the heater core. Put regular coolant in it then drive, drive, drive. It will break loose. Mine took nearly 4 months to get the sludge out of the radiator even after flush. But it worked. Manufacturer will never comment about that DEX crap.I have a 98 and I had the same problem..it was my heater core, they arent hard to replace and I dont think they are that expensive
Where is the fuel cut off switch located in a 1986 Ford Bronco 2?
there is a switch on the passenger side floor board under the dash. if you pull the carpet down it's close to the center hump,it's square with a reset button on the top.
What is the tire size on a 2001 jetta gls vr6?
195/50/15
The question specified a 2001 VW Jetta VR6 GLS THESE are 205/55/16s.
How to change headlamp and turn signal bulbs on 2000-2005 Taurus?
To replace headlight bulb:
- Make sure headlight switch is turned OFF.
- Remove the bolt at the end of the headlamp housing.
- Pull the two black tabs with the L shaped bracket toward the back and then up and pull out(Located at the back of the headlamp) to release the headlamp assembly from the vehicle and pull headlamp assembly forward.
- Disconnect the electrical connector from the bulb by pulling it.
- Remove the bulb socket retaining ring by rotating it counterclockwise.
- Remove the bulb from the lamp assembly by pulling straight back.
Do not twist, as there are alignment slots built into the lamp assembly socket.
It may take some effort to remove the lamp because it has a rubber o-ring type seal - try a bit of wiggling side-to-side
- Insert new bulb into headlight assembly - don't touch the glass - use gloves, paper towel, or similar
Make sure that the flat surface of the bulb socket is facing upward, and is firmly seated
- Re-attach retainer ring by rotating clockwise
- Reconnect the electrical harness
- Re-install headlight assembly - hold snugly into place until the brackets line up and retainer pins can be pushed down
Replacing front parking lamp/turn signal/cornering lamp bulbs
- Remove headlight / lens assembly per above steps
- Rotate the bulb socket of the offending bulb counterclockwise and remove from the lamp assembly.
- Carefully pull bulb straight out of the socket and push in the new bulb
- Install the bulb socket into the headlight assembly by rotating it clockwise
- Re-install headlight assembly - hold snugly into place until the brackets line up and retainer pins can be pushed down
- Do not touch the glass of the new halogen bulb - the oils in the skin will shorten the life-span of the new bulb, or possibly cause the bulb to explode when first turned on
If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used.
- This procedure is well detailed, with illustrations, in the Owners Manual.
See "Related Questions" below in case you can't find yours.
- FRONT Turn-signal - 3457 AK (amber)
- Headlamp - 9007 QL (9007LL optional)
- Tail lamp/brake/turn lamp 3157
- Tail lamp/brake lamp (wagon) 3157
- Rear turn lamp (wagon) 3456K
- Backup lamp 921
- Backup lamp (wagon) 3156
- License plate lamp (2) 168
- High-mount brake lamp (2) 912
- Rear side marker lamp (wagon) (2) 168
The above information extracted from the Owners Manuals(see below)
Remove screws holding the plastic headlight and remove the headlight. Remove socket (twist/pull) and pull out the bulb.
DIY - 5 Minute Turn Signal Bulb ReplacementThis is very simple to do. First you will need an 8mm socket and wrench to loosen one bolt. Second a good long flat head screwdriver. There are two black metal folded tabs behind the headlight assembly and one 8mm bolt holding it in plae at the center point of the front of the car. Loosen the bolt and remove. Use the screw driver to pull up the metal straps and then slide forward the entire assembly. This will slide easily unless your front bumper has been bumped! That will make it a little difficult to slide if it is out of alignment. If it was never bumped than this should take all of 5 minutes. See pictures here:http://204.200.208.247/taurus_bulb
It's actually quite easy. You must remove the entire plastic housing. Behind the light there ate two locking bars that slip up and down. Remove those and a screw holding the light/lens in place. From there remove the bulb covering, then remove the twist lock holding the bulb in place. After that, just pull the bulb out and replace. Put back in reverse order.
Open the hood, looking down at the headlamp assembly, you'll see a 5/16 retaining bolt on the inboard corner. Remove the bolt. Look for two tabs at the rear of the assembly. Pull up and remove these tabs, you may need a large screwdriver to lever them. Pull the assembly out and remove the wiring harness attachment. Turn the retaining collar to the left and remove. Unplug the wiring socket from the lamp. Turn the lamp retaining collar to the left and remove. Pull the lamp out of the assembly. Replace with the new lamp, being VERY careful not to touch the lamp other than on the base. Halogen lamps will heat up any oils from contact with your hand and probably explode. Reverse the above directions to reinstall the headlamp assembly.
Very easy. 2002 Ford Taurus.
Take a look at the entire headlight assembly. Look down on the assembly and toward the side closest the radiator you will see a small bolt to unscrew on each housing.
Look toward the rear of the headlight and you will see two metal clips that need to come out. A medium size flathead will get them started but they should come staight up. The assembly will now pull out of the front of the vehicle. Be sure to unclip the small wiring harness.
Uncrew the back of the assembly and you will see the back of the bulb. Detach wiring. Unscrew the ring holding the lamp. Remove old bulb.
DO NOT touch the glass of your lamps! It will cause hot spots and the bulb will burn out.
Take new bulb and notice the notches...they will orient the bulb correctly. Screw on ring. Attach wiring. Screw on the back of the assembly. Attach the wiring and install back into the front of your vehicle.
The headlight lens is held in with 1 bolt on the front inside end of the lens, and 2 retainer pins at the backside (pull straight up to remove).
The Owners Manual has the steps and illustrations around page 37.
See "Related Questions" below for free online Owners Manual
Where is the PCM on a 2002 Cavalier?
according to the haynes book i have it is located in the right rear corner of the engine compartment
Are there any known issues with 38l Ford engines?
They always blow the head gaskets between 70 and 100 thousand miles.
